[RADIATOR] Radiator

[Heikki Vatiainen]

On 03/22/2012 07:05 AM, Sudhir Harwalkar wrote:

> I have replaced current <client> clause with whatever you mentioned below, but in log file it shows an error.

There's still one line left from the old <Client> clause. Remove this
line too:

<Client your.client.dns.name.com>

> Please see the command line message in screenshot "cmd_msg.PNG" also see the log file attached with this.

You can set log directory with the command line options, but I suggest
you replace 'LogDir' and 'DbDir' with these values:

LogDir          c:/Program Files/Radiator
DbDir           c:/Program Files/Radiator

You should use the new Client clause and the above LogDir and DbDir
values in the other configurations files you also try.

> Yes my AP IP is 192.168.37.184.

Ok. Thanks. More about this in your other message, but briefly:
- this address goes into Client: <Client 192.168.37.184>
- BindAddress is local address. Use 0.0.0.0 in most cases

> In the log file as I found .directory is not found need to mention the path for directory?
>  If possible please make changes in the log file attached with this and send me, I will verify with this.

Try the changes above and try running it then.

Thanks!
Heikki


> Thanks in Advance
> Sudhir H
> 
> 
> -----Original Message-----
> From: radiator-bounces at open.com.au [mailto:radiator-bounces at open.com.au] On Behalf Of Heikki Vatiainen
> Sent: Thursday, March 22, 2012 4:08 AM
> To: radiator at open.com.au
> Subject: Re: [RADIATOR] Radiator
> 
> On 03/21/2012 11:40 AM, Sudhir Harwalkar wrote:
> 
>> Thanks Heikki, I installed Net-SSLeay.ppd.
> 
> Ok, good to hear.
> 
>> 1.Please find the radius.cfg file, in that I have added AP IP address and Authentication port, is that correct way that I mentioned in the config file radius.cfg file or need to make some other things and where do I need to mention Shared Secrete.
> 
> Try replacing your current <Client> clause with this:
> 
> Trace 4
> LogStdout
> AuthPort 1812
> AcctPort 1813
> # This clause defines a single client to listen to <Client 192.168.37.184>
>         Secret   GSDEMO
> </Client>
> 
> AuthPort and AcctPort do not go into Client and I am assuming
> 192.168.37.184 is your AP.
> 
> I added Trace 4 and LogStdout so that you will easily see the debug and other messages on the console.
> 
>> 2. send me command for running radius.cfg file, that I have stored in c:/ProgramFile.
> 
> First, see http://www.open.com.au/radiator/install-demo.html and the installation instructions there. They give examples how to start radiusd (Radiator).
> 
> Typically something like this should work:
> 
> perl c:\perl\bin\radiusd -trace 4 -config_file c:\path\to\your.conf
> 
> --
> Heikki Vatiainen <hvn at open.com.au>
> 
> Radiator: the most portable, flexible and configurable RADIUS server anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc.
> _______________________________________________
> radiator mailing list
> radiator at open.com.au
> http://www.open.com.au/mailman/listinfo/radiator
> 
> 
> Larsen & Toubro Limited
> 
> www.larsentoubro.com
> 
> This Email may contain confidential or privileged information for the intended recipient (s) If you are not the intended recipient, please do not use or disseminate the information, notify the sender and delete it from your system.


-- 
Heikki Vatiainen <hvn at open.com.au>

Radiator: the most portable, flexible and configurable RADIUS server
anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald,
Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS,
TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP,
DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS,
NetWare etc.