[RADIATOR] FW: Radiator

Sudhir Harwalkar Sudhir.Harwalkar at lnties.com
Tue Mar 27 05:41:48 CDT 2012 

If I delete the  <Client DEFAULT> also Its using the port 1645 and 1646.
Please find the log file and config file.

Thanks
Sudhir

-----Original Message-----
From: radiator-bounces at open.com.au [mailto:radiator-bounces at open.com.au] On Behalf Of Heikki Vatiainen
Sent: Tuesday, March 27, 2012 3:40 PM
To: radiator at open.com.au
Subject: Re: [RADIATOR] FW: Radiator

On 03/27/2012 11:19 AM, Sudhir Harwalkar wrote:

Hello Sudhir,

> I modified the file according to your changes, that works fine.
> There are some queries:
>
> 1. In the config file if I mentioned Auth PORT and ACCTPORT then it's taking as 1645 and 1646, and I tried with the command line means I gave authport and acctport its taking properly.

I took another look at your configuration file and noticed there is still an extra line. Remove this:

<Client DEFAULT>

since the real Client clause is just below. The extra lines was before AuthPort and AcctPort lines causing them to be parsed within Client context which is not corrrect.

> 2. I gave UserName and Password for both WLAN Device and Radius Server, but its not able to associated with the AP and Radius server, how to verify that all three AP,WLAN Device and Radius Server are communicating with each other.

When you have enabled Trace 4, you should see messages from AP in Radiator's log file. Are you seeing anything? Please reply with the log especially if there are errors or warnings in it.

Thanks!
Heikki


> Thanks
> Sudhir H
>
> -----Original Message-----
> From: radiator-bounces at open.com.au
> [mailto:radiator-bounces at open.com.au] On Behalf Of Heikki Vatiainen
> Sent: Monday, March 26, 2012 1:35 PM
> To: radiator at open.com.au list
> Subject: Re: [RADIATOR] Radiator
>
> On 03/26/2012 02:54 PM, Sudhir Harwalkar wrote:
>
> Hello Sudhir,
>
>> Please find the modified EAP-PEAPv0 file, please check once whether whatever changes I made are correct or not, please see the error message attached with this peaperror.PNG.
>
> Try defining your using slash '/' instead of backslash '\'. For example:
>
> LogDir C:/Radiator/Radiator-Locked-4.9/goodies/
>
> I also recommend defining LogDir and DbDir to point to where Radiator installed its configuration file. Typically this is:
>
> C:/Program Files/Radiator/
>
> The directory specified with DbDir should also have file called dictionary. If not, you need to specify DictionaryFile to point to that file.
>
> Other changes: You have specified files and directories with '%C:\...'.
> You do not need to use '%' sign here. Use for example:
>
> Filename C:/Radiator/Radiator-Locked-4.9/users
> instead of
> Filename %C:\Radiator\Radiator-Locked-4.9/users
>
> Here I also recommend setting AuthBy FILE Filename to C:/Program Files/Radiator/users if C:/Program Files/Radiator/ already contains e.g., dictionary file.
>
> Related to this and your previous message. The simplest users file would have just this one line:
>
> username User-Password=mypassword
>
> This creates users file which knows about one user 'username' and where the user has password 'mypassword'.
>
> Thanks!
> Heikki
>
>
>> Thanks
>> Sudhir H
>>
>> -----Original Message-----
>> From: Sudhir Harwalkar
>> Sent: Monday, March 26, 2012 10:53 AM
>> To: 'Heikki Vatiainen'
>> Subject: RE: [RADIATOR] Radiator
>>
>> Hi Heikki,
>>
>> How to add device username and password in our config file.is there any command for that.
>>
>> Thanks
>> Sudhir H
>>
>> -----Original Message-----
>> From: Sudhir Harwalkar
>> Sent: Thursday, March 22, 2012 3:49 PM
>> To: 'Heikki Vatiainen'
>> Subject: RE: [RADIATOR] Radiator
>>
>> Thanks a lot Heikki, will try and let you know.
>>
>> Thanks
>> Sudhir H
>>
>> -----Original Message-----
>> From: radiator-bounces at open.com.au
>> [mailto:radiator-bounces at open.com.au] On Behalf Of Heikki Vatiainen
>> Sent: Thursday, March 22, 2012 3:23 PM
>> To: radiator at open.com.au
>> Subject: Re: [RADIATOR] Radiator
>>
>> On 03/22/2012 11:44 AM, Sudhir Harwalkar wrote:
>>> I made all the changes you have mentioned, then I run the config file, in the log file I got message as follows
>>>         Thu Mar 22 15:00:17 2012: DEBUG: Finished reading configuration file 'c:\Program Files\Radiator\radiusnew.cfg'
>>>                 Thu Mar 22 15:00:17 2012: DEBUG: Reading dictionary file 'C:\Program Files\Radiator/dictionary'
>>>                 Thu Mar 22 15:00:17 2012: DEBUG: Creating authentication port 0.0.0.0:1812
>>>                Thu Mar 22 15:00:17 2012: DEBUG: Creating accounting port 0.0.0.0:1813
>>>                 Thu Mar 22 15:00:17 2012: NOTICE: Server started:
>>> Radiator 4.9 on EMMYS0938 (LOCKED) Is this authenticated with AP?
>>
>> Looks good. It is ready to receive messages from AP. There is no authentication done between RADIUS server and wireless AP. The shared secret and client IP just make sure they can communicate with each other when the WLAN users need to be authenticated by the AP.
>>
>>> As you mentioned I haven't got message like receives from AP.
>>
>> The next step is to configure AP so that it will authenticate WLAN users. How this is done depends on your AP.
>>
>> Thanks!
>> Heikki
>>
>>
>>> Regards
>>> Sudhir H
>>> -----Original Message-----
>>> From: radiator-bounces at open.com.au
>>> [mailto:radiator-bounces at open.com.au] On Behalf Of Heikki Vatiainen
>>> Sent: Thursday, March 22, 2012 2:22 PM
>>> To: radiator at open.com.au
>>> Subject: Re: [RADIATOR] Radiator
>>>
>>> On 03/21/2012 03:58 PM, Sudhir Harwalkar wrote:
>>>
>>>> Thanks a lot for helping me out.
>>>> I have one query :
>>>>  Steps that I followed for EAP-PEAPv0 Testing:
>>>>         1. Copied eap_peap.cfg file to c:\program file
>>>
>>> Add a Client clause with your AP's address in the configuration. Also set DbDir and LogDir as I just mentioned in my other message:
>>>
>>> LogDir          c:/Program Files/Radiator
>>> DbDir           c:/Program Files/Radiator
>>>
>>>>         2. in the command line I typed the command "perl radiusd
>>>> -bind_address 192. . . . -auth_port 1812 -log_file filename
>>>> -config_file c:\program files\eap_peap.cfg When I run this command
>>>> I am getting an error, the error details are shown in the
>>>> screenshot named as eap_peap.PNG
>>>
>>> You do not need to set BindAddress. If set, it should be address belonging to your computer, not to the AP. You usually do not need to set this at all.
>>>
>>>> - Is there anything that I need to make change?
>>>
>>> Please see above.
>>>
>>>> -How does we know that communication happening between AP and Radius Server?
>>>
>>> The log will messages Radiator receives from AP.
>>>
>>>> -Port address that I have given in AP is 1812 is that right?
>>>
>>> Please see above. About auth_port, it should match the setting in AP. By default Radiator uses 1645 so you need to check both AP and Radiator use same port number.
>>>
>>>> -please see the config file that I have used is attached with this mail.
>>>
>>> I suggest you try seeing simple authentication without PEAP works before moving to PEAP configuration. If your AP provides a method to authenticate users with plain username and password (no PEAP involved), this would be the best method to see the basic communication between AP and Radiator works.
>>>
>>> Thanks!
>>> Heikki
>>>
>>>
>>>>
>>>> Thanks
>>>> Sudhir H
>>>>
>>>>
>>>> Larsen & Toubro Limited
>>>>
>>>> www.larsentoubro.com
>>>>
>>>> This Email may contain confidential or privileged information for the intended recipient (s) If you are not the intended recipient, please do not use or disseminate the information, notify the sender and delete it from your system.
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> radiator mailing list
>>>> radiator at open.com.au
>>>> http://www.open.com.au/mailman/listinfo/radiator
>>>
>>>
>>> --
>>> Heikki Vatiainen <hvn at open.com.au>
>>>
>>> Radiator: the most portable, flexible and configurable RADIUS server anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc.
>>> _______________________________________________
>>> radiator mailing list
>>> radiator at open.com.au
>>> http://www.open.com.au/mailman/listinfo/radiator
>>>
>>>
>>> Larsen & Toubro Limited
>>>
>>> www.larsentoubro.com
>>>
>>> This Email may contain confidential or privileged information for the intended recipient (s) If you are not the intended recipient, please do not use or disseminate the information, notify the sender and delete it from your system.
>>> _______________________________________________
>>> radiator mailing list
>>> radiator at open.com.au
>>> http://www.open.com.au/mailman/listinfo/radiator
>>
>>
>> --
>> Heikki Vatiainen <hvn at open.com.au>
>>
>> Radiator: the most portable, flexible and configurable RADIUS server anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc.
>> _______________________________________________
>> radiator mailing list
>> radiator at open.com.au
>> http://www.open.com.au/mailman/listinfo/radiator
>>
>>
>> Larsen & Toubro Limited
>>
>> www.larsentoubro.com
>>
>> This Email may contain confidential or privileged information for the intended recipient (s) If you are not the intended recipient, please do not use or disseminate the information, notify the sender and delete it from your system.
>>
>>
>>
>> _______________________________________________
>> radiator mailing list
>> radiator at open.com.au
>> http://www.open.com.au/mailman/listinfo/radiator
>
>
> --
> Heikki Vatiainen <hvn at open.com.au>
>
> Radiator: the most portable, flexible and configurable RADIUS server anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc.
> _______________________________________________
> radiator mailing list
> radiator at open.com.au
> http://www.open.com.au/mailman/listinfo/radiator
>
>
> Larsen & Toubro Limited
>
> www.larsentoubro.com
>
> This Email may contain confidential or privileged information for the intended recipient (s) If you are not the intended recipient, please do not use or disseminate the information, notify the sender and delete it from your system.
> _______________________________________________
> radiator mailing list
> radiator at open.com.au
> http://www.open.com.au/mailman/listinfo/radiator


--
Heikki Vatiainen <hvn at open.com.au>

Radiator: the most portable, flexible and configurable RADIUS server anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc.
_______________________________________________
radiator mailing list
radiator at open.com.au
http://www.open.com.au/mailman/listinfo/radiator


Larsen & Toubro Limited

www.larsentoubro.com

This Email may contain confidential or privileged information for the intended recipient (s) If you are not the intended recipient, please do not use or disseminate the information, notify the sender and delete it from your system.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: peap.log
Type: application/octet-stream
Size: 578 bytes
Desc: peap.log
Url : http://www.open.com.au/pipermail/radiator/attachments/20120327/b3360a18/attachment-0002.obj 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: eap_peap.cfg
Type: application/octet-stream
Size: 11122 bytes
Desc: eap_peap.cfg
Url : http://www.open.com.au/pipermail/radiator/attachments/20120327/b3360a18/attachment-0003.obj

More information about the radiator mailing list