[RADIATOR] Installation on OpenWRT

[Andrea Coppini (AIR Networks)]

Package info:

Package: perlbase-extutils
Version: 5.10.0-2
Depends: perl
Provides: 
Source: feeds/packages/lang/perl
Section: lang
Priority: optional
Maintainer: Peter Colberg <peter at petercolberg.org>
Architecture: metarouter
Installed-Size: 515262
Filename: perlbase-extutils_5.10.0-2_metarouter.ipk
Size: 142072
MD5Sum: 554e68044a0e362139a52039d79712a2
Description:  ExtUtils perl module



-----Original Message-----
From: radiator-bounces at open.com.au [mailto:radiator-bounces at open.com.au] On
Behalf Of Andrea Coppini (AIR Networks)
Sent: 19 August 2010 6:55 PM
To: radiator at open.com.au
Subject: Re: [RADIATOR] Installation on OpenWRT

Line 14 of Makefile.pl has "use ExtUtils::Install".

I'm suspecting ExtUtils are old or incomplete, how do I check which version
they are?  Remember I have installed these with OPKG, from the source at
http://openwrt.pantele.com.ua/trunk/metarouter/packages

TOP only shows 8644k are being used, but I've now increased the RAM
allocation to 64Mb to be safe.

Regards
Andrea

-----Original Message-----
From: radiator-bounces at open.com.au [mailto:radiator-bounces at open.com.au] On
Behalf Of Alexander Hartmaier
Sent: 19 August 2010 6:09 PM
To: radiator at open.com.au
Subject: Re: [RADIATOR] Installation on OpenWRT

Hi,

Radiator is written in Perl, so check line 14 of Makefile.PL and figure
out what's going wrong.
Maybe some of your Perl modules are too old.
32MB of memory are really not much!
Radiator takes 28MB on our prod server which isn't really a lot for a
Perl app.

--
Best regards, Alex


Am Donnerstag, den 19.08.2010, 17:16 +0200 schrieb Andrea Coppini (AIR
Networks):
> Hi,
>
> I'm trying to install Radiator on an OpenWRT OS (www.openwrt.org).  I have
> 256Mb of disk and 32Mb of RAM allocated to OpenWRT, which should be
plenty.
>
> I have installed all the Perl and Perlbase modules successfully, and
> unzipped Radiator-Locked-4.7 to the root.  I'm logged in as root, no
> password (this is a test system).
>
> When I run 'perl Makefile.PL', I get the following error:
> ----
> ExtUtils/Install.pm did not return a true value at Makefile.PL line 14.
> BEGIN failed--compilation aborted at Makefile.PL line 14.
> ----
> Any ideas what this might be? And how I could fix it?
>
>
> Regards
> Andrea
>
>
> _______________________________________________
> radiator mailing list
> radiator at open.com.au
> http://www.open.com.au/mailman/listinfo/radiator


*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"
*
T-Systems Austria GesmbH   Rennweg 97-99, 1030 Wien
Handelsgericht Wien, FN 79340b
*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"
*
Notice: This e-mail contains information that is confidential and may be
privileged.
If you are not the intended recipient, please notify the sender and then
delete this e-mail immediately.
*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"*"
*
_______________________________________________
radiator mailing list
radiator at open.com.au
http://www.open.com.au/mailman/listinfo/radiator

_______________________________________________
radiator mailing list
radiator at open.com.au
http://www.open.com.au/mailman/listinfo/radiator