(RADIATOR) Problem of Radiator MAXT TNT
Muhammad Farooq Bhatti
farooq.bhatti at comsats.net.pk
Fri Aug 13 14:20:29 CDT 2004
Dear hugh
Thanx for the clue of using authplsql.pm I will try it later but even after
removing one of
<SessionDatabase SQL> its log is same as mentioned. If you could guide me
why
Ascend-Disconnect-Cause = 101
Ascend-Connect-Progress = 67
is comming in Access-request stop packet. of "comsats" user connection on
MAX TNT for multi-login.
where as ascend itself explain that
Disconect-cause=101 is for The session failed for security reasons, such as
an invalid incoming user.
Connect-Progress = 67 is for IPNCP is in the Open state.
One more favour if u can guide is how can I make "disconnect cause code" to
readable in MAX like in cisco we get propper
Acct-Terminat-casue.
e.g. in ciscoAs5300,
Acct-Terminate-Cause = User-Request
Thanx and regards.
Farooq Bhatti.
----- Original Message -----
From: "Hugh Irvine" <hugh at open.com.au>
To: "Muhammad Farooq Bhatti" <farooq.bhatti at comsats.net.pk>
Cc: <radiator at open.com.au>
Sent: Thursday, August 12, 2004 4:05 PM
Subject: Re: (RADIATOR) Problem of Radiator MAXT TNT
>
> Hello Farooq -
>
> I think at least part of your problem is shown below - you have two
> <SessionDatabase SQL> lines and as you can see the debug log is _very_
> confused. You should remove one of the lines and try your tests again.
>
>
> <SessionDatabase SQL>
> <SessionDatabase SQL>
> DBSource dbi:Oracle:host=x.x.x.x;sid=x;port=1521
> DBUsername xxxx
> DBAuth xxxxxx
> Timeout 60
>
> AddQuery insert into RADONLINE (USERNAME, NASIDENTIFIER,
> NASPORT, \
> ACCTSESSIONID, TIME_STAMP, FRAMEDIPADDRESS,
> NASPORTTYPE, \
> SERVICETYPE) values ('%u', '%N', 0%{NAS-Port},
> '%{Acct-Session-Id}',\
> %{Timestamp}, '%{Framed-IP-Address}',
> '%{NAS-Port-Type}', \
> '%{Service-Type}')
>
>
> DeleteQuery delete from RADONLINE where NASIDENTIFIER='%1' and
> NASPORT=0%2
>
> </SessionDatabase SQL>
>
>
> BTW - You may find it easier to code at least some of your processing
> in Oracle stored procedures. You will find an AuthPLSQL.pm module that
> you can use for this purpose in the "goodies" directory.
>
> regards
>
> Hugh
>
>
>
> On 13 Aug 2004, at 12:52, Muhammad Farooq Bhatti wrote:
>
> > Dear hugh
> >
> > Please read uptill end; sorry its too large
> >
> > ########## Start of config ##########
> > AcctPort 1646
> > AuthPort 1645
> > DbDir .
> > DictionaryFile /cibs/radius/Radiator-3.9/dictionary
> > FingerProg /usr/bin/finger
> > LogDir .
> > LogFile /var/log/radius/radlog
> > LogStdout
> > PidFile /tmp/radiusd.pid
> > SnmpgetProg /usr/local/bin/snmpget
> > Trace 5
> >
> >
> > <SessionDatabase SQL>
> > <SessionDatabase SQL>
> > DBSource
> > dbi:Oracle:host=x.x.x.x;sid=x;port=1521
> > DBUsername xxxx
> > DBAuth xxxxxx
> > Timeout 60
> >
> > AddQuery insert into RADONLINE (USERNAME, NASIDENTIFIER,
> > NASPORT, \
> > ACCTSESSIONID, TIME_STAMP, FRAMEDIPADDRESS,
> > NASPORTTYPE, \
> > SERVICETYPE) values ('%u', '%N', 0%{NAS-Port},
> > '%{Acct-Session-Id}',\
> > %{Timestamp}, '%{Framed-IP-Address}',
> > '%{NAS-Port-Type}', \
> > '%{Service-Type}')
> >
> >
> > DeleteQuery delete from RADONLINE where NASIDENTIFIER='%1' and
> > NASPORT=0%2
> >
> > </SessionDatabase SQL>
> >
> >
> >
> >
> > <Client X.X.x.>
> > Secret xxxxxxx
> > </Client>
> >
> > <Client DEFAULT>
> > Secret xxxxxx
> > DupInterval 0
> > </Client>
> >
> >
> > ############################
> >
> >
> >
> > <Realm DEFAULT>
> >
> >
> > <AuthBy SQL>
> > DBSource
> > dbi:Oracle:host=x.x.x.x;sid=x;port=1521
> > DBUsername xxxx
> > DBAuth xxxxx
> > Timeout 60
> >
> >
> >
> > AddToReply
> > Framed-Protocol=%{Framed-Protocol},Service-Type=%{Service-Type},Port-
> > Limit=2
> >
> > AuthSelect select A.PASSWORD , B.SIMULTANEOUS_USE,
> > B.FRAMED_IP_ADDRESS,
> > B.FRAMED_IP_NETMASK, B.FRAMED_ROUTE, B
> > .FILTER_ID, B.FILTER_ID_OUT, B.CISCO_AV_PAIR,
> > B.FRAMED_ROUTE2,B.FRAMED_ROUTE3, GET_RADIUS_SESSION_TIME_OUT(%0)
> > SESSION_TIMEOUT , D.TimeString from \
> > customer_info A, Customer_account B,
> > customer_contacts C,
> > Tariff D \
> > where A.tariff_Id = D.tariff_Id AND \
> > ( \
> > ( \
> > (lOWER(NVL(C.OFF_CLI1,'no'))='yes' AND
> > (C.OFFICE_PHONE1='%{Calling-Station-Id}' OR C.OF
> > FICE_PHONE1='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.OFF_CLI2,'no'))='yes' AND
> > (C.OFFICE_PHONE2='%{Calling-Station-Id}' OR C.OF
> > FICE_PHONE2='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.OFF_CLI3,'no'))='yes' AND
> > (C.OFFICE_PHONE3='%{Calling-Station-Id}' OR C.OF
> > FICE_PHONE3='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.OFF_CLI4,'no'))='yes' AND
> > (C.OFFICE_PHONE4='%{Calling-Station-Id}' OR C.OF
> > FICE_PHONE4='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.RES_CLI1,'no'))='yes' AND
> > (C.RES_PHONE1='%{Calling-Station-Id}' OR C.RES_P
> > HONE1='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.RES_CLI2,'no'))='yes' AND
> > (C.RES_PHONE2='%{Calling-Station-Id}' OR C.RES_P
> > HONE2='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.RES_CLI3,'no'))='yes' AND
> > (C.RES_PHONE3='%{Calling-Station-Id}' OR C.RES_P
> > HONE3='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.RES_CLI4,'no'))='yes' AND
> > (C.RES_PHONE4='%{Calling-Station-Id}' OR C.RES_P
> > HONE4='0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.FAX_CLI1,'no'))='yes' AND
> > (C.FAX1='%{Calling-Station-Id}' OR C.FAX1='0%{Ca
> > lling-Station-Id}') ) OR \
> > (lOWER(NVL(C.FAX_CLI2,'no'))='yes' AND
> > (C.FAX2='%{Calling-Station-Id}' OR C.FAX2='0%{Ca
> > lling-Station-Id}') ) OR \
> > (lOWER(NVL(C.MOB_CLI1,'no'))='yes' AND
> > (C.MOBILE1='%{Calling-Station-Id}' OR C.MOBILE1=
> > '0%{Calling-Station-Id}') ) OR \
> > (lOWER(NVL(C.MOB_CLI2,'no'))='yes' AND
> > (C.MOBILE2='%{Calling-Station-Id}' OR C.MOBILE2=
> > '0%{Calling-Station-Id}') ) \
> > ) \
> > OR \
> > ( \
> > lOWER(NVL(C.OFF_CLI1,'no'))='no' AND \
> > lOWER(NVL(C.OFF_CLI2,'no'))='no' AND \
> > lOWER(NVL(C.OFF_CLI3,'no'))='no' AND \
> > lOWER(NVL(C.OFF_CLI4,'no'))='no' AND \
> > lOWER(NVL(C.RES_CLI1,'no'))='no' AND \
> > lOWER(NVL(C.RES_CLI2,'no'))='no' AND \
> > lOWER(NVL(C.RES_CLI3,'no'))='no' AND \
> > lOWER(NVL(C.RES_CLI4,'no'))='no' AND \
> > lOWER(NVL(C.FAX_CLI1,'no'))='no' AND \
> > lOWER(NVL(C.FAX_CLI2,'no'))='no' AND \
> > lOWER(NVL(C.MOB_CLI1,'no'))='no' AND \
> > lOWER(NVL(C.MOB_CLI2,'no'))='no' \
> > ) \
> > ) AND \
> > A.customer_id = C.Customer_id (+) AND \
> > sysDate < B.EXPIRY_DATE AND \
> > B.ACCOUNT_BALANCE >= B.Credit_Limit AND \
> > UPPER(B.Status) ='ACTIVE' AND \
> > A.customer_id = B.Customer_id AND \
> > A.login_Id=%0
> >
> > AuthColumnDef 0, Encrypted-Password, check
> > AuthColumnDef 1, Simultaneous-Use, check
> > AuthColumnDef 2, Framed-IP-Address, reply
> > AuthColumnDef 3, Framed-IP-Netmask, reply
> > AuthColumnDef 4, Framed-Route, reply
> > AuthColumnDef 5, Filter-Id, reply
> > AuthColumnDef 6, Filter-Id, reply
> > AuthColumnDef 7, cisco-avpair, reply
> > AuthColumnDef 8, Framed-Route, reply
> > AuthColumnDef 9, Framed-Route, reply
> > AuthColumnDef 10, Session-Timeout, reply
> > AuthColumnDef 11, Time, check
> >
> >
> > AccountingTable RadiusDump
> > AcctColumnDef ACCT_SESSION_ID, Acct-Session-Id
> > #AcctColumnDef TIMESTAMP,Timestamp,integer-date,
> > %e/%b/%y
> > #AcctColumnDef TIMESTAMP,Timestamp,integer-date,
> > %e/%b/%y%H:%M:%S
> > #AcctColumnDef TIMESTAMP,Timestamp,integer
> > AcctColumnDef
> > TIMESTAMP,Timestamp,formatted-date,to_date
> > ('%e %m %Y %H: %M: %S','DD MM YYYY HH2
> > 4:MI:SS')
> > AcctColumnDef Acct_Delay_Time, Acct-Delay-Time
> > AcctColumnDef USER_NAME, User-Name
> > AcctColumnDef ACCT_STATUS_TYPE, Acct-Status-Type
> > AcctColumnDef ACCT_SESSION_TIME, Acct-Session-Time
> > AcctColumnDef ACCT_MULTI_SESSION_ID,
> > Acct-Multi-Session-Id
> > AcctColumnDef ACCT_LINK_COUNT, Acct-Link-Count
> > AcctColumnDef SERVICE_TYPE, Framed-Protocol
> > AcctColumnDef NAS_Identifier, NAS-Identifier
> > AcctColumnDef NAS_IP_ADDRESS, NAS-IP-Address
> > AcctColumnDef NAS_PORT, NAS-Port
> > AcctColumnDef NAS_PORT_TYPE, NAS-Port-Type
> > AcctColumnDef ACCT_AUTHENTIC, Acct-Authentic
> > AcctColumnDef ACCT_INPUT_PACKETS, Acct-Input-Packets
> > AcctColumnDef ACCT_OUTPUT_PACKETS, Acct-Output-Packets
> > AcctColumnDef ACCT_INPUT_OCTETS, Acct-Input-Octets
> > AcctColumnDef ACCT_OUTPUT_OCTETS, Acct-Output-Octets
> > AcctColumnDef CALLED_STATION_ID, Called-Station-Id
> > AcctColumnDef ACCT_TERMINATE_CAUSE,
> > Acct-Terminate-Cause
> > AcctColumnDef CALLING_STATION_ID, Calling-Station-Id
> >
> > </AuthBy>
> >
> >
> > AcctLogFileFormat %o %{NAS-IP-Address} %{User-Name}
> > %{Acct-Session-Id} \
> > %{NAS-Port-Type} %{NAS-Port} %{Acct-Status-Type}
> > %{Service-Type} %{Framed-Protocol} \
> > %{Calling-Station-Id} %{Acct-Session-Time}
> > %{Acct-Terminate-Cause} %{Framed-IP-Address}
> >
> > AcctLogFileName /var/log/radius/cibsRadiusAaccount.log
> >
> > </Realm>
> > #
> > #
> > #
> > ###the end #########################
> >
> > ############# The trace 5 log for user comsats on MAX TNT
> >
> > Packet length = 148
> > 01 dd 00 94 af 3d 17 e8 0f 24 24 72 48 6a c3 67
> > 1e 80 d0 30 01 0a 63 6f 6d 73 61 74 73 00 02 07
> > df db ae 1b 67 04 06 cb d7 bf 02 20 20 53 57 41
> > 54 2d 43 49 53 2d 4d 61 78 54 4e 54 2e 63 6f 6d
> > 73 61 74 73 2e 6e 65 74 2e 70 6b 05 06 00 00 00
> > 1a 3d 06 00 00 00 00 18 02 1f 0c 30 39 33 36 37
> > 31 32 39 38 37 2c 0c 34 34 36 34 36 32 32 35 38
> > 00 6d 17 01 13 01 48 be 6a 98 40 62 a8 83 c5 42
> > 34 7a 10 7d 00 00 00 00 c5 06 00 00 67 20 ff 06
> > 00 00 c5 eb
> > Code: Access-Request
> > Identifier: 221
> > Authentic: <175>=<23><232><15>$$rHj<195>g<30><128><208>0
> > Attributes:
> > User-Name = "comsats"
> > User-Password = "<223><219><174><27>g"
> > NAS-IP-Address = 203.215.191.2
> > NAS-Identifier = "SWAT-CIS-MaxTNT.comsats.net.pk"
> > NAS-Port = 26
> > NAS-Port-Type = Async
> > State = ""
> > Calling-Station-Id = "0936712987"
> > Acct-Session-Id = "446462258"
> > Ascend-Endpoint-Disc =
> > "<1><19><1>H<190>j<152>@b<168><131><197>B4z<16>}"
> > Ascend-Data-Rate = 26400
> > Ascend-Xmit-Rate = 50667
> >
> >
> > Wed Aug 11 17:56:37 2004: DEBUG: Handling request with Handler
> > 'Realm=DEFAULT'
> > Wed Aug 11 17:56:37 2004: DEBUG: Deleting session for comsats,
> > 203.215.191.2, 26
> > Wed Aug 11 17:56:37 2004: DEBUG: do query is: 'delete from RADONLINE
> > where
> > NASIDENTIFIER='203.215.191.2' and NA
> > SPORT=026':
> >
> > Wed Aug 11 17:56:37 2004: DEBUG: Handling with Radius::AuthSQL
> > Wed Aug 11 17:56:37 2004: DEBUG: Handling with Radius::AuthSQL:
> > Wed Aug 11 17:56:37 2004: DEBUG: Query is: 'select A.PASSWORD ,
> > B.SIMULTANEOUS_USE, B.FRAMED_IP_ADDRESS, B.FRAM
> > ED_IP_NETMASK, B.FRAMED_ROUTE, B.FILTER_ID, B.FILTER_ID_OUT,
> > B.CISCO_AV_PAIR, B.FRAMED_ROUTE2,B.FRAMED_ROUTE3,
> > GET_RADIUS_SESSION_TIME_OUT('comsats') SESSION_TIMEOUT , D.TimeString
> > from
> > customer_info A, Customer_account
> > B, customer_contacts C, Tariff D where A.tariff_Id = D.tariff_Id AND (
> > (
> > (lOWER(NVL(C.OFF_CLI1,'no'))='yes' AND
> > (C.OFFICE_PHONE1='0936712987' OR C.OFFICE_PHONE1='00936712987') ) OR
> > (lOWER(NVL(C.OFF_CLI2,'no'))='yes' AND (
> > C.OFFICE_PHONE2='0936712987' OR C.OFFICE_PHONE2='00936712987') ) OR
> > (lOWER(NVL(C.OFF_CLI3,'no'))='yes' AND (C.O
> > FFICE_PHONE3='0936712987' OR C.OFFICE_PHONE3='00936712987') ) OR
> > (lOWER(NVL(C.OFF_CLI4,'no'))='yes' AND (C.OFFI
> > CE_PHONE4='0936712987' OR C.OFFICE_PHONE4='00936712987') ) OR
> > (lOWER(NVL(C.RES_CLI1,'no'))='yes' AND (C.RES_PHO
> > NE1='0936712987' OR C.RES_PHONE1='00936712987') ) OR
> > (lOWER(NVL(C.RES_CLI2,'no'))='yes' AND (C.RES_PHONE2='0936
> > 712987' OR C.RES_PHONE2='00936712987') ) OR
> > (lOWER(NVL(C.RES_CLI3,'no'))='yes' AND (C.RES_PHONE3='0936712987' O
> > R C.RES_PHONE3='00936712987') ) OR (lOWER(NVL(C.RES_CLI4,'no'))='yes'
> > AND
> > (C.RES_PHONE4='0936712987' OR C.RES_P
> > HONE4='00936712987') ) OR (lOWER(NVL(C.FAX_CLI1,'no'))='yes' AND
> > (C.FAX1='0936712987' OR C.FAX1='00936712987')
> > ) OR (lOWER(NVL(C.FAX_CLI2,'no'))='yes' AND (C.FAX2='0936712987' OR
> > C.FAX2='00936712987') ) OR (lOWER(NVL(C.MOB
> > _CLI1,'no'))='yes' AND (C.MOBILE1='0936712987' OR
> > C.MOBILE1='00936712987') )
> > OR (lOWER(NVL(C.MOB_CLI2,'no'))='y
> > es' AND (C.MOBILE2='0936712987' OR C.MOBILE2='00936712987') ) ) OR (
> > lOWER(NVL(C.OFF_CLI1,'no'))='no' AND lOWER
> > (NVL(C.OFF_CLI2,'no'))='no' AND lOWER(NVL(C.OFF_CLI3,'no'))='no' AND
> > lOWER(NVL(C.OFF_CLI4,'no'))='no' AND lOWER
> > (NVL(C.RES_CLI1,'no'))='no' AND lOWER(NVL(C.RES_CLI2,'no'))='no' AND
> > lOWER(NVL(C.RES_CLI3,'no'))='no' AND lOWER
> > (NVL(C.RES_CLI4,'no'))='no' AND lOWER(NVL(C.FAX_CLI1,'no'))='no' AND
> > lOWER(NVL(C.FAX_CLI2,'no'))='no' AND lOWER
> > (NVL(C.MOB_CLI1,'no'))='no' AND lOWER(NVL(C.MOB_CLI2,'no'))='no' ) )
> > AND
> > A.customer_id = C.Customer_id (+) AND
> > sysDate < B.EXPIRY_DATE AND B.ACCOUNT_BALANCE >= B.Credit_Limit AND
> > UPPER(B.Status) ='ACTIVE' AND A.customer_id
> > = B.Customer_id AND A.login_Id='comsats'':
> >
> > Wed Aug 11 17:56:37 2004: DEBUG: Radius::AuthSQL looks for match with
> > comsats
> > Wed Aug 11 17:56:37 2004: DEBUG: Query is: 'select NASIDENTIFIER,
> > NASPORT,
> > ACCTSESSIONID, FRAMEDIPADDRESS from
> > RADONLINE where USERNAME='comsats'':
> >
> > Wed Aug 11 17:56:37 2004: DEBUG: Radius::AuthSQL ACCEPT:
> > Wed Aug 11 17:56:37 2004: DEBUG: Access accepted for comsats
> > Wed Aug 11 17:56:37 2004: DEBUG: Packet dump:
> > *** Sending to 203.215.191.2 port 527 ....
> >
> > Packet length = 50
> > 02 dd 00 32 83 4f 71 16 20 f2 f4 75 4f d8 c2 fd
> > 16 cd bd b9 09 06 ff ff ff ff 1b 06 00 03 f4 80
> > 07 06 00 00 00 00 06 06 00 00 00 00 3e 06 00 00
> > 00 02
> > Code: Access-Accept
> > Identifier: 221
> > Authentic: <175>=<23><232><15>$$rHj<195>g<30><128><208>0
> > Attributes:
> > Framed-IP-Netmask = 255.255.255.255
> > Session-Timeout = 259200
> > Framed-Protocol =
> > Service-Type =
> > Port-Limit = 2
> >
> > Wed Aug 11 17:56:37 2004: DEBUG: Packet dump:
> > *** Received from 203.215.191.2 port 7018 ....
> >
> > Packet length = 212
> > 04 7b 00 d4 ef 87 bf b6 38 ac f0 8d 39 cb d9 b4
> > be db 4a d0 37 06 41 1a 63 43 04 06 cb d7 bf 02
> > 20 20 53 57 41 54 2d 43 49 53 2d 4d 61 78 54 4e
> > 54 2e 63 6f 6d 73 61 74 73 2e 6e 65 74 2e 70 6b
> > 05 06 00 00 00 1a 3d 06 00 00 00 00 28 06 00 00
> > 00 02 29 06 00 00 00 00 2c 0c 34 34 36 34 36 32
> > 32 35 38 00 c3 06 00 00 00 65 c4 06 00 00 00 43
> > c5 06 00 00 67 20 c6 06 00 00 00 18 be 06 00 00
> > 01 86 bf 06 00 00 01 57 c0 06 00 00 00 0f c1 06
> > 00 00 00 0f ff 06 00 00 c5 eb bb 06 bf 02 03 41
> > bc 06 00 00 00 00 33 06 00 00 00 01 32 0a 62 66
> > 30 32 30 33 34 31 78 06 00 00 00 03 79 06 00 00
> > 00 05 7a 06 00 00 00 01 1f 0c 30 39 33 36 37 31
> > 32 39 38 37
> > Code: Accounting-Request
> > Identifier: 123
> > Authentic:
> > <239><135><191><182>8<172><240><141>9<203><217><180><190><219>J<208>
> > Attributes:
> > Event-Timestamp = 1092248387
> > NAS-IP-Address = 203.215.191.2
> > NAS-Identifier = "SWAT-CIS-MaxTNT.comsats.net.pk"
> > NAS-Port = 26
> > NAS-Port-Type = Async
> > Acct-Status-Type = Stop
> > Acct-Delay-Time = 0
> > Acct-Session-Id = "446462258"
> > Ascend-Disconnect-Cause = 101
> > Ascend-Connect-Progress = 67
> > Ascend-Data-Rate = 26400
> > Ascend-PreSession-Time = 24
> > Ascend-Pre-Input-Octets = 390
> > Ascend-Pre-Output-Octets = 343
> > Ascend-Pre-Input-Packets = 15
> > Ascend-Pre-Output-Packets = 15
> > Ascend-Xmit-Rate = 50667
> > Ascend-Multilink-ID = 3204580161
> > Ascend-Num-In-Multilink = 0
> > Acct-Link-Count = 1
> > Acct-Multi-Session-Id = "bf020341"
> > Ascend-Modem-PortNo = 3
> > Ascend-Modem-SlotNo = 5
> > Ascend-Modem-ShelfNo = 1
> > Calling-Station-Id = "0936712987"
> >
> > Wed Aug 11 17:56:37 2004: DEBUG: Handling request with Handler
> > 'Realm=DEFAULT'
> > Wed Aug 11 17:56:37 2004: DEBUG: Deleting session for ,
> > 203.215.191.2, 26
> > Wed Aug 11 17:56:37 2004: DEBUG: do query is: 'delete from RADONLINE
> > where
> > NASIDENTIFIER='203.215.191.2' and NA
> > SPORT=026':
> >
> > Wed Aug 11 17:56:37 2004: DEBUG: Handling with Radius::AuthSQL
> > Wed Aug 11 17:56:37 2004: DEBUG: Handling accounting with
> > Radius::AuthSQL
> > Wed Aug 11 17:56:37 2004: DEBUG: do query is: 'insert into RadiusDump
> > (NAS_PORT_TYPE,ACCT_SESSION_ID,NAS_PORT,T
> > IMESTAMP,ACCT_LINK_COUNT,NAS_IP_ADDRESS,ACCT_STATUS_TYPE,CALLING_STATIO
> > N_ID,
> > NAS_Identifier,ACCT_MULTI_SESSION_I
> > D,Acct_Delay_Time) values ('Async','446462258','26',to_date ('11 08
> > 2004 17:
> > 56: 37','DD MM YYYY HH24:MI:SS'),'
> > 1','203.215.191.2','Stop','0936712987','SWAT-CIS-
> > MaxTNT.comsats.net.pk','bf0
> > 20341','0')':
> >
> > ############################# End of log #############
> >
> > ############# Trace on Cisco AS5300 for user cnonews
> >
> > Code: Access-Request
> > Identifier: 24
> > Authentic:
> > <223><210><135><226><167><187>7<14><169><222><137><232><158><216>Iw
> > Attributes:
> > Framed-Protocol = PPP
> > User-Name = "cnonews"
> > User-Password =
> > "<235>n<228><158><240>:<138><238><16><184><188><246>4<2>#<157>"
> > NAS-Port = 20019
> > NAS-Port-Type = ISDN
> > Calling-Station-Id = "0519225440"
> > Service-Type = Framed-User
> > NAS-IP-Address = 210.56.8.143
> >
> > Thu Aug 12 19:24:32 2004: DEBUG: Handling request with Handler
> > 'Realm=DEFAULT'
> > Thu Aug 12 19:24:32 2004: DEBUG: Deleting session for cnonews,
> > 210.56.8.143, 20019
> > Thu Aug 12 19:24:32 2004: DEBUG: do query is: 'delete from RADONLINE
> > where
> > NASIDENTIFIER='210.56.8.143' and NAS
> > PORT=020019':
> >
> > Thu Aug 12 19:24:32 2004: DEBUG: Handling with Radius::AuthSQL
> > Thu Aug 12 19:24:32 2004: DEBUG: Handling with Radius::AuthSQL:
> > Thu Aug 12 19:24:32 2004: DEBUG: Query is: 'select A.PASSWORD ,
> > B.SIMULTANEOUS_USE, B.FRAMED_IP_ADDRESS, B.FRAM
> > ED_IP_NETMASK, B.FRAMED_ROUTE, B.FILTER_ID, B.FILTER_ID_OUT,
> > B.CISCO_AV_PAIR, B.FRAMED_ROUTE2,B.FRAMED_ROUTE3,
> > GET_RADIUS_SESSION_TIME_OUT('cnonews') SESSION_TIMEOUT, D.TimeString
> > from
> > customer_info A, Customer_account B
> > , customer_contacts C, Tariff D where A.tariff_Id = D.tariff_Id AND ( (
> > (lOWER(NVL(C.OFF_CLI1,'no'))='yes' AND
> > (C.OFFICE_PHONE1='0519225440' OR C.OFFICE_PHONE1='00519225440') ) OR
> > (lOWER(NVL(C.OFF_CLI2,'no'))='yes' AND (C
> > .OFFICE_PHONE2='0519225440' OR C.OFFICE_PHONE2='00519225440') ) OR
> > (lOWER(NVL(C.OFF_CLI3,'no'))='yes' AND (C.OF
> > FICE_PHONE3='0519225440' OR C.OFFICE_PHONE3='00519225440') ) OR
> > (lOWER(NVL(C.OFF_CLI4,'no'))='yes' AND (C.OFFIC
> > E_PHONE4='0519225440' OR C.OFFICE_PHONE4='00519225440') ) OR
> > (lOWER(NVL(C.RES_CLI1,'no'))='yes' AND (C.RES_PHON
> > E1='0519225440' OR C.RES_PHONE1='00519225440') ) OR
> > (lOWER(NVL(C.RES_CLI2,'no'))='yes' AND (C.RES_PHONE2='05192
> > 25440' OR C.RES_PHONE2='00519225440') ) OR
> > (lOWER(NVL(C.RES_CLI3,'no'))='yes' AND (C.RES_PHONE3='0519225440' OR
> > C.RES_PHONE3='00519225440') ) OR (lOWER(NVL(C.RES_CLI4,'no'))='yes'
> > AND
> > (C.RES_PHONE4='0519225440' OR C.RES_PH
> > ONE4='00519225440') ) OR (lOWER(NVL(C.FAX_CLI1,'no'))='yes' AND
> > (C.FAX1='0519225440' OR C.FAX1='00519225440') )
> > OR (lOWER(NVL(C.FAX_CLI2,'no'))='yes' AND (C.FAX2='0519225440' OR
> > C.FAX2='00519225440') ) OR (lOWER(NVL(C.MOB_
> > CLI1,'no'))='yes' AND (C.MOBILE1='0519225440' OR
> > C.MOBILE1='00519225440') )
> > OR (lOWER(NVL(C.MOB_CLI2,'no'))='ye
> > s' AND (C.MOBILE2='0519225440' OR C.MOBILE2='00519225440') ) ) OR (
> > lOWER(NVL(C.OFF_CLI1,'no'))='no' AND lOWER(
> > NVL(C.OFF_CLI2,'no'))='no' AND lOWER(NVL(C.OFF_CLI3,'no'))='no' AND
> > lOWER(NVL(C.OFF_CLI4,'no'))='no' AND lOWER(
> > NVL(C.RES_CLI1,'no'))='no' AND lOWER(NVL(C.RES_CLI2,'no'))='no' AND
> > lOWER(NVL(C.RES_CLI3,'no'))='no' AND lOWER(
> > NVL(C.RES_CLI4,'no'))='no' AND lOWER(NVL(C.FAX_CLI1,'no'))='no' AND
> > lOWER(NVL(C.FAX_CLI2,'no'))='no' AND lOWER(
> > NVL(C.MOB_CLI1,'no'))='no' AND lOWER(NVL(C.MOB_CLI2,'no'))='no' ) ) AND
> > A.customer_id = C.Customer_id (+) AND s
> > ysDate < B.EXPIRY_DATE AND B.ACCOUNT_BALANCE >= B.Credit_Limit AND
> > UPPER(B.Status) ='ACTIVE' AND A.customer_id
> > = B.Customer_id AND A.login_Id='cnonews'':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Radius::AuthSQL looks for match with
> > cnonews
> > Thu Aug 12 19:24:34 2004: DEBUG: Query is: 'select NASIDENTIFIER,
> > NASPORT,
> > ACCTSESSIONID, FRAMEDIPADDRESS from
> > RADONLINE where USERNAME='cnonews'':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Radius::AuthSQL ACCEPT:
> > Thu Aug 12 19:24:34 2004: DEBUG: Access accepted for cnonews
> > Thu Aug 12 19:24:34 2004: DEBUG: Packet dump:
> > *** Sending to 210.56.8.143 port 1645 ....
> > Code: Access-Accept
> > Identifier: 24
> > Authentic:
> > <223><210><135><226><167><187>7<14><169><222><137><232><158><216>Iw
> > Attributes:
> > Framed-Protocol = PPP
> > Service-Type = Framed-User
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Packet dump:
> > *** Received from 210.56.8.143 port 1646 ....
> > Code: Accounting-Request
> > Identifier: 213
> > Authentic: <140>V<215><1><30><214>n\q<164><8><160><226><9>]<1>
> > Attributes:
> > Acct-Session-Id = "00061E4D"
> > Framed-Protocol = PPP
> > Acct-Authentic = RADIUS
> > Acct-Status-Type = Start
> > User-Name = "cnonews"
> > Acct-Multi-Session-Id = "0003D41A"
> > Acct-Link-Count = 1
> > NAS-Port = 20019
> > NAS-Port-Type = ISDN
> > Calling-Station-Id = "0519225440"
> > Service-Type = Framed-User
> > NAS-IP-Address = 210.56.8.143
> > Acct-Delay-Time = 0
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling request with Handler
> > 'Realm=DEFAULT'
> > Thu Aug 12 19:24:34 2004: DEBUG: Adding session for cnonews,
> > 210.56.8.143,
> > 20019
> > Thu Aug 12 19:24:34 2004: DEBUG: do query is: 'delete from RADONLINE
> > where
> > NASIDENTIFIER='210.56.8.143' and NAS
> > PORT=020019':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: do query is: 'insert into RADONLINE
> > (USERNAME, NASIDENTIFIER, NASPORT, ACCTSES
> > SIONID, TIME_STAMP, FRAMEDIPADDRESS, NASPORTTYPE, SERVICETYPE) values
> > ('cnonews', '210.56.8.143', 020019, '0006
> > 1E4D',1092320674, '', 'ISDN', 'Framed-User')':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling with Radius::AuthSQL
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling accounting with
> > Radius::AuthSQL
> > Thu Aug 12 19:24:34 2004: DEBUG: do query is: 'insert into RadiusDump
> > (ACCT_AUTHENTIC,ACCT_LINK_COUNT,ACCT_MULT
> > I_SESSION_ID,ACCT_SESSION_ID,ACCT_STATUS_TYPE,Acct_Delay_Time,CALLING_S
> > TATIO
> > N_ID,NAS_IP_ADDRESS,NAS_PORT,NAS_PO
> > RT_TYPE,SERVICE_TYPE,TIMESTAMP,USER_NAME) values
> > ('RADIUS','1','0003D41A','00061E4D','Start','0','0519225440','
> > 210.56.8.143','20019','ISDN','PPP',to_date ('12 08 2004 19: 24:
> > 34','DD MM
> > YYYY HH24:MI:SS'),'cnonews')':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Accounting accepted
> > Thu Aug 12 19:24:34 2004: DEBUG: Packet dump:
> > *** Sending to 210.56.8.143 port 1646 ....
> > Code: Accounting-Response
> > Identifier: 213
> > Authentic: <140>V<215><1><30><214>n\q<164><8><160><226><9>]<1>
> > Attributes:
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Packet dump:
> > *** Received from 210.56.8.143 port 1645 ....
> >
> >
> > Code: Access-Request
> > Identifier: 25
> > Authentic:
> > <223><210><135><226><167><187>7<14><169><222><137><232><158><216>Iw
> > Attributes:
> > Framed-Protocol = PPP
> > User-Name = "cnonews"
> > User-Password =
> > "<235>n<228><158><240>:<138><238><16><184><188><246>4<2>#<157>"
> > NAS-Port = 20206
> > NAS-Port-Type = ISDN
> > Calling-Station-Id = "0519225440"
> > Service-Type = Framed-User
> > NAS-IP-Address = 210.56.8.143
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling request with Handler
> > 'Realm=DEFAULT'
> > Thu Aug 12 19:24:34 2004: DEBUG: Deleting session for cnonews,
> > 210.56.8.143, 20206
> > Thu Aug 12 19:24:34 2004: DEBUG: do query is: 'delete from RADONLINE
> > where
> > NASIDENTIFIER='210.56.8.143' and NAS
> > PORT=020206':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling with Radius::AuthSQL
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling with Radius::AuthSQL:
> > Thu Aug 12 19:24:34 2004: DEBUG: Query is: 'select A.PASSWORD ,
> > B.SIMULTANEOUS_USE, B.FRAMED_IP_ADDRESS, B.FRAM
> > ED_IP_NETMASK, B.FRAMED_ROUTE, B.FILTER_ID, B.FILTER_ID_OUT,
> > B.CISCO_AV_PAIR, B.FRAMED_ROUTE2,B.FRAMED_ROUTE3,
> > GET_RADIUS_SESSION_TIME_OUT('cnonews') SESSION_TIMEOUT, D.TimeString
> > from
> > customer_info A, Customer_account B
> > , customer_contacts C, Tariff D where A.tariff_Id = D.tariff_Id AND ( (
> > (lOWER(NVL(C.OFF_CLI1,'no'))='yes' AND
> > (C.OFFICE_PHONE1='0519225440' OR C.OFFICE_PHONE1='00519225440') ) OR
> > (lOWER(NVL(C.OFF_CLI2,'no'))='yes' AND (C
> > .OFFICE_PHONE2='0519225440' OR C.OFFICE_PHONE2='00519225440') ) OR
> > (lOWER(NVL(C.OFF_CLI3,'no'))='yes' AND (C.OF
> > FICE_PHONE3='0519225440' OR C.OFFICE_PHONE3='00519225440') ) OR
> > (lOWER(NVL(C.OFF_CLI4,'no'))='yes' AND (C.OFFIC
> > E_PHONE4='0519225440' OR C.OFFICE_PHONE4='00519225440') ) OR
> > (lOWER(NVL(C.RES_CLI1,'no'))='yes' AND (C.RES_PHON
> > E1='0519225440' OR C.RES_PHONE1='00519225440') ) OR
> > (lOWER(NVL(C.RES_CLI2,'no'))='yes' AND (C.RES_PHONE2='05192
> > 25440' OR C.RES_PHONE2='00519225440') ) OR
> > (lOWER(NVL(C.RES_CLI3,'no'))='yes' AND (C.RES_PHONE3='0519225440' OR
> > C.RES_PHONE3='00519225440') ) OR (lOWER(NVL(C.RES_CLI4,'no'))='yes'
> > AND
> > (C.RES_PHONE4='0519225440' OR C.RES_PH
> > ONE4='00519225440') ) OR (lOWER(NVL(C.FAX_CLI1,'no'))='yes' AND
> > (C.FAX1='0519225440' OR C.FAX1='00519225440') )
> > OR (lOWER(NVL(C.FAX_CLI2,'no'))='yes' AND (C.FAX2='0519225440' OR
> > C.FAX2='00519225440') ) OR (lOWER(NVL(C.MOB_
> > CLI1,'no'))='yes' AND (C.MOBILE1='0519225440' OR
> > C.MOBILE1='00519225440') )
> > OR (lOWER(NVL(C.MOB_CLI2,'no'))='ye
> > s' AND (C.MOBILE2='0519225440' OR C.MOBILE2='00519225440') ) ) OR (
> > lOWER(NVL(C.OFF_CLI1,'no'))='no' AND lOWER(
> > NVL(C.OFF_CLI2,'no'))='no' AND lOWER(NVL(C.OFF_CLI3,'no'))='no' AND
> > lOWER(NVL(C.OFF_CLI4,'no'))='no' AND lOWER(
> > NVL(C.RES_CLI1,'no'))='no' AND lOWER(NVL(C.RES_CLI2,'no'))='no' AND
> > lOWER(NVL(C.RES_CLI3,'no'))='no' AND lOWER(
> > NVL(C.RES_CLI4,'no'))='no' AND lOWER(NVL(C.FAX_CLI1,'no'))='no' AND
> > lOWER(NVL(C.FAX_CLI2,'no'))='no' AND lOWER(
> > NVL(C.MOB_CLI1,'no'))='no' AND lOWER(NVL(C.MOB_CLI2,'no'))='no' ) ) AND
> > A.customer_id = C.Customer_id (+) AND s
> > ysDate < B.EXPIRY_DATE AND B.ACCOUNT_BALANCE >= B.Credit_Limit AND
> > UPPER(B.Status) ='ACTIVE' AND A.customer_id
> > = B.Customer_id AND A.login_Id='cnonews'':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Radius::AuthSQL looks for match with
> > cnonews
> > Thu Aug 12 19:24:34 2004: DEBUG: Query is: 'select NASIDENTIFIER,
> > NASPORT,
> > ACCTSESSIONID, FRAMEDIPADDRESS from
> > RADONLINE where USERNAME='cnonews'':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Radius::AuthSQL ACCEPT:
> > Thu Aug 12 19:24:34 2004: DEBUG: Access accepted for cnonews
> > Thu Aug 12 19:24:34 2004: DEBUG: Packet dump:
> > *** Sending to 210.56.8.143 port 1645 ....
> > Code: Access-Accept
> > Identifier: 25
> > Authentic:
> > <223><210><135><226><167><187>7<14><169><222><137><232><158><216>Iw
> > Attributes:
> > Framed-Protocol = PPP
> > Service-Type = Framed-User
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Packet dump:
> > *** Received from 210.56.8.143 port 1646 ....
> > Code: Accounting-Request
> > Identifier: 214
> > Authentic: S<201><169><20>gf:j7<6><182><18>g|<156>4
> > Attributes:
> > Acct-Session-Id = "00061E4D"
> > Framed-Protocol = PPP
> > Acct-Session-Time = 0
> > Acct-Input-Octets = 110
> > Acct-Output-Octets = 112
> > Acct-Input-Packets = 4
> > Acct-Output-Packets = 5
> > Acct-Authentic = RADIUS
> > Acct-Status-Type = Alive
> > User-Name = "cnonews"
> > Acct-Multi-Session-Id = "0003D41A"
> > Acct-Link-Count = 1
> > Framed-IP-Address = 210.56.9.235
> > NAS-Port = 20019
> > NAS-Port-Type = ISDN
> > Calling-Station-Id = "0519225440"
> > Service-Type = Framed-User
> > NAS-IP-Address = 210.56.8.143
> > Acct-Delay-Time = 0
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling request with Handler
> > 'Realm=DEFAULT'
> > Thu Aug 12 19:24:34 2004: DEBUG: Adding session for cnonews,
> > 210.56.8.143,
> > 20019
> > Thu Aug 12 19:24:34 2004: DEBUG: do query is: 'delete from RADONLINE
> > where
> > NASIDENTIFIER='210.56.8.143' and NAS
> > PORT=020019':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: do query is: 'insert into RADONLINE
> > (USERNAME, NASIDENTIFIER, NASPORT, ACCTSES
> > SIONID, TIME_STAMP, FRAMEDIPADDRESS, NASPORTTYPE, SERVICETYPE) values
> > ('cnonews', '210.56.8.143', 020019, '0006
> > 1E4D',1092320674, '210.56.9.235', 'ISDN', 'Framed-User')':
> >
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling with Radius::AuthSQL
> > Thu Aug 12 19:24:34 2004: DEBUG: Handling accounting with
> > Radius::AuthSQL
> > Thu Aug 12 19:24:34 2004: DEBUG: do query is: 'insert into RadiusDump
> > (ACCT_AUTHENTIC,ACCT_INPUT_OCTETS,ACCT_IN
> > PUT_PACKETS,ACCT_LINK_COUNT,ACCT_MULTI_SESSION_ID,ACCT_OUTPUT_OCTETS,AC
> > CT_OU
> > TPUT_PACKETS,ACCT_SESSION_ID,ACCT_S
> > ESSION_TIME,ACCT_STATUS_TYPE,Acct_Delay_Time,CALLING_STATION_ID,NAS_IP_
> > ADDRE
> > SS,NAS_PORT,NAS_PORT_TYPE,SERVICE_T
> > YPE,TIMESTAMP,USER_NAME) values
> > ('RADIUS','110','4','1','0003D41A','112','5','00061E4D','0','Alive','0'
> > ,'051
> > 922
> > 5440','210.56.8.143','20019','ISDN','PPP',to_date ('12 08 2004 19: 24:
> > 34','DD MM YYYY HH24:MI:SS'),'cnonews')'
> > :
> >
> > Thu Aug 12 19:24:35 2004: DEBUG: Accounting accepted
> > Thu Aug 12 19:24:35 2004: DEBUG: Packet dump:
> > *** Sending to 210.56.8.143 port 1646 ....
> > Code: Accounting-Response
> > Identifier: 214
> > Authentic: S<201><169><20>gf:j7<6><182><18>g|<156>4
> > Attributes:
> >
> > Thu Aug 12 19:24:35 2004: DEBUG: Packet dump:
> > *** Received from 210.56.8.143 port 1646 ....
> > Code: Accounting-Request
> > Identifier: 215
> > Authentic: R<10>N<128><240><1>`<210><187><247><157><157><146><226>'-
> > Attributes:
> > Acct-Session-Id = "00061E4E"
> > Framed-Protocol = PPP
> > Acct-Authentic = RADIUS
> > Acct-Status-Type = Start
> > User-Name = "cnonews"
> > Acct-Multi-Session-Id = "0003D41A"
> > Acct-Link-Count = 2
> > Framed-IP-Address = 210.56.9.235
> > NAS-Port = 20206
> > NAS-Port-Type = ISDN
> > Calling-Station-Id = "0519225440"
> > Service-Type = Framed-User
> > NAS-IP-Address = 210.56.8.143
> > Acct-Delay-Time = 0
> >
> > Thu Aug 12 19:24:35 2004: DEBUG: Handling request with Handler
> > 'Realm=DEFAULT'
> > Thu Aug 12 19:24:35 2004: DEBUG: Adding session for cnonews,
> > 210.56.8.143,
> > 20206
> > Thu Aug 12 19:24:35 2004: DEBUG: do query is: 'delete from RADONLINE
> > where
> > NASIDENTIFIER='210.56.8.143' and NAS
> > PORT=020206':
> >
> > Thu Aug 12 19:24:35 2004: DEBUG: do query is: 'insert into RADONLINE
> > (USERNAME, NASIDENTIFIER, NASPORT, ACCTSES
> > SIONID, TIME_STAMP, FRAMEDIPADDRESS, NASPORTTYPE, SERVICETYPE) values
> > ('cnonews', '210.56.8.143', 020206, '0006
> > 1E4E',1092320675, '210.56.9.235', 'ISDN', 'Framed-User')':
> >
> > Thu Aug 12 19:24:35 2004: DEBUG: Handling with Radius::AuthSQL
> > Thu Aug 12 19:24:35 2004: DEBUG: Handling accounting with
> > Radius::AuthSQL
> > Thu Aug 12 19:24:35 2004: DEBUG: do query is: 'insert into RadiusDump
> > (ACCT_AUTHENTIC,ACCT_LINK_COUNT,ACCT_MULT
> > I_SESSION_ID,ACCT_SESSION_ID,ACCT_STATUS_TYPE,Acct_Delay_Time,CALLING_S
> > TATIO
> > N_ID,NAS_IP_ADDRESS,NAS_PORT,NAS_PO
> > RT_TYPE,SERVICE_TYPE,TIMESTAMP,USER_NAME) values
> > ('RADIUS','2','0003D41A','00061E4E','Start','0','0519225440','
> > 210.56.8.143','20206','ISDN','PPP',to_date ('12 08 2004 19: 24:
> > 35','DD MM
> > YYYY HH24:MI:SS'),'cnonews')':
> >
> > Thu Aug 12 19:24:35 2004: DEBUG: Accounting accepted
> > Thu Aug 12 19:24:35 2004: DEBUG: Packet dump:
> > *** Sending to 210.56.8.143 port 1646 ....
> > Code: Accounting-Response
> > Identifier: 215
> > Authentic: R<10>N<128><240><1>`<210><187><247><157><157><146><226>'-
> > Attributes:
> >
> > Thu Aug 12 19:24:45 2004: DEBUG: Packet dump:
> > *** Received from 210.56.8.145 port 1646 ....
> >
> >
> > ########## Note it repeat the two CODES of access-request and
> > accountig-request for 2nd login
> >
> >
> >
> >
> >
> >
> >
> >
> > ##########################################
> >
> >
> > please advice, I personaly thing that it seems to be some problem with
> > MAX
> > tnt
> >
> > Regards Farooq
> >
> > ----- Original Message -----
> > From: "Hugh Irvine" <hugh at open.com.au>
> > To: "Muhammad Farooq Bhatti" <farooq.bhatti at comsats.net.pk>
> > Cc: <radiator at open.com.au>
> > Sent: Thursday, August 12, 2004 3:52 AM
> > Subject: Re: (RADIATOR) Problem of Radiator MAXT TNT
> >
> >
> >>
> >> Hello Farooq -
> >>
> >> Could you please send me a copy of your configuration file (no
> >> secrets)
> >> together with a trace 4 debug from Radiator showing what is happening
> >> with an access request, an accounting start and an accounting stop
> >> with
> >> both the Cisco and the Ascend.
> >>
> >> regards
> >>
> >> Hugh
> >>
> >>
> >> On 13 Aug 2004, at 06:59, Muhammad Farooq Bhatti wrote:
> >>
> >>> Dear all,
> >>>
> >>> After doing a lot of search without positive result, finally I am
> >>> going to write u.
> >>>
> >>> I have MAX TNT with 10.1.0 TAOS and Radiator 3.9 , I am getting a
> >>> problem of Multi-login where as MPP i.e., multilink is working fine.
> >>>
> >>> I am using same with Cisco AS5300 without any problem plz let me know
> >>> what could be wrong.
> >>>
> >>> For any further info let me know.
> >>>
> >>> Muhammad Farooq Bhatti
> >>> Assistant Director (Systems)
> >>> First Floor, COMSATS Headquarters,
> >>> Shahra-e-Jamhuriyat, G-5/2, Islamabad
> >>> Ph. +92-51-9208063-5 Ext. 124
> >>> Fax. +92-51-9212411
> >>> farooq.bhatti at comsats.net.pk
> >>> www.comsats.net.pk
> >>>
> >>
> >> NB: have you included a copy of your configuration file (no secrets),
> >> together with a trace 4 debug showing what is happening?
> >>
> >> --
> >> Radiator: the most portable, flexible and configurable RADIUS server
> >> anywhere. Available on *NIX, *BSD, Windows, MacOS X.
> >> -
> >> Nets: internetwork inventory and management - graphical, extensible,
> >> flexible with hardware, software, platform and database independence.
> >> -
> >> CATool: Private Certificate Authority for Unix and Unix-like systems.
> >>
> >> --
> >> Archive at http://www.open.com.au/archives/radiator/
> >> Announcements on radiator-announce at open.com.au
> >> To unsubscribe, email 'majordomo at open.com.au' with
> >> 'unsubscribe radiator' in the body of the message.
> >>
> >
> >
>
> NB: have you included a copy of your configuration file (no secrets),
> together with a trace 4 debug showing what is happening?
>
> --
> Radiator: the most portable, flexible and configurable RADIUS server
> anywhere. Available on *NIX, *BSD, Windows, MacOS X.
> -
> Nets: internetwork inventory and management - graphical, extensible,
> flexible with hardware, software, platform and database independence.
> -
> CATool: Private Certificate Authority for Unix and Unix-like systems.
>
--
Archive at http://www.open.com.au/archives/radiator/
Announcements on radiator-announce at open.com.au
To unsubscribe, email 'majordomo at open.com.au' with
'unsubscribe radiator' in the body of the message.
More information about the radiator
mailing list