(RADIATOR) Bad login count
Hugh Irvine
hugh at open.com.au
Mon Dec 10 22:38:08 CST 2001
Hello Chairath -
The log message shown below is due to the username "user2 at test2" not being
found in the database. This is probably because you have not used a
RewriteUsername in the Handler to strip the realm (you should use the same
one that you used in the Realm clause).
regards
Hugh
On Tue, 11 Dec 2001 15:17, Chairath K wrote:
> Hello Hugh,
>
> I have got problem about Bad login count. According to section 5.1.9 in
> reference manual of RAdmin version 1.4 , it said that if we leave this
> field blank, then no bad login limits will be applied. But !! when I try ,
> I can't login . In log file shows a message like these
>
>
> Tue Dec 11 10:53:56 2001: INFO: Access rejected for user2 at test2: No such
> user Tue Dec 11 10:53:56 2001: DEBUG: Packet dump:
> *** Sending to 10.20.0.2 port 49156 ....
> Code: Access-Reject
> Identifier: 159
> Authentic: <0><0>4G<0><0><13><21><0><0><31>><0><0>/<172>
> Attributes:
> Reply-Message = "Request Denied"
>
> So how can I fixed it .
> Futhermore , how can I expand login limit to more than 5
>
> Regards,
> Chairath
>
> P.S. Our system are running with Radiator 2.18 and Radmin 1.4
>
> Foreground
> LogStdout
> LogDir d:/Radiator-2.18/log
> DbDir d:/Radiator-2.18
> LogFile %L/logfile-%d-%m-%Y
>
> # Dont turn this up too high, since all log messages are logged
> # to the RADMESSAGES table in the database. 3 will give you everything
> # except debugging messages
> Trace 4
>
>
> # PreClientHook to add NAS-Port attribute
> PreClientHook file:"%D/addNASPort"
>
> # You will probably want to change this to suit your site.
> # You should list all the clients you have, and their secrets
> # If you are using the Radmin Clients table, you wil probably
> # want to disable this.
> #<Client DEFAULT>
> # Secret mysecret
> # DupInterval 0
> #</Client>
>
> # You can put additonal (or all) client details in your Radmin
> # database table
> # and get their details from there with something like this:
> # You can then use the Radmin 'Add Radius Client' to add new clients.
> <ClientListSQL>
> DBSource dbi:ODBC:Radmin
> DBUsername xxx
> DBAuth xxxx
> </ClientListSQL>
>
> #<AuthBy RADIUS>
> # Identifier ProxyTofunk
> # Host 10.2.0.6
> # Secret test
> #</AuthBy>
>
> #<Realm funk>
> # strip Realm
> # RewriteUsername s/^([^@]+).*/$1/
> # AuthBy ProxyTofunk
> #</Realm>
>
> <AuthBy RADMIN>
> Identifier RADMINAUTH
> # Change DBSource, DBUsername, DBAuth for your database
> # See the reference manual. You will also have to
> # change the one in <SessionDatabse SQL> below
> # so its the same
> DBSource dbi:ODBC:Radmin
> DBUsername xxx
> DBAuth xxxx
> DateFormat %e %m %Y %T
> # You can add to or change these if you want, but you
> # will probably want to change the database schema first
> AccountingTable RADUSAGE
> AcctColumnDef USERNAME,User-Name
> AcctColumnDef TIME_STAMP,Timestamp,integer
> AcctColumnDef ACCTSTATUSTYPE,Acct-Status-Type,integer
> AcctColumnDef ACCTDELAYTIME,Acct-Delay-Time,integer
> AcctColumnDef ACCTINPUTOCTETS,Acct-Input-Octets,integer
> AcctColumnDef ACCTOUTPUTOCTETS,Acct-Output-Octets,integer
> AcctColumnDef ACCTSESSIONID,Acct-Session-Id
> AcctColumnDef ACCTSESSIONTIME,Acct-Session-Time,integer
> AcctColumnDef ACCTTERMINATECAUSE,Acct-Terminate-Cause,integer
> AcctColumnDef FRAMEDIPADDRESS,Framed-IP-Address
> AcctColumnDef NASIDENTIFIER,NAS-Identifier
> AcctColumnDef NASIDENTIFIER,NAS-IP-Address
> AcctColumnDef NASPORT,NAS-Port,integer
> AcctColumnDef DNIS,Called-Station-Id
> AcctColumnDef DATE,Timestamp,integer-date
> # This updates the time and octets left
> # for this user
> AcctSQLStatement update RADUSERS set
> TIMELEFT=TIMELEFT-0%{Acct-Session-Time},
> OCTETSINLEFT=OCTETSINLEFT-0%{Acct-Input-Octets},
> OCTETSOUTLEFT=OCTETSOUTLEFT-0%{Acct-Output-Octets} where USERNAME='%n'
>
> </AuthBy>
>
> <AuthBy GROUP>
> Identifier WithIdleTimeout
> AuthBy RADMINAUTH
> # These are the classic things to add to each users
> # reply to allow a PPP dialup session. It may be
> # different for your NAS. This will add some
> # reply items to everyone's reply
> AddToReply Framed-Protocol = PPP,\
> Service-Type = Framed-User,\
> Framed-IP-Netmask = 255.255.255.255,\
> Framed-Routing = None,\
> Framed-MTU = 1500,\
> Framed-Compression = Van-Jacobson-TCP-IP,\
> Idle-Timeout = 600,\
> Class = %{NAS-Port}
> </AuthBy>
>
> <AuthBy GROUP>
> Identifier WithOutIdleTimeout
> AuthBy RADMINAUTH
> # These are the classic things to add to each users
> # reply to allow a PPP dialup session. It may be
> # different for your NAS. This will add some
> # reply items to everyone's reply
> AddToReply Framed-Protocol = PPP,\
> Service-Type = Framed-User,\
> Framed-IP-Netmask = 255.255.255.255,\
> Framed-Routing = None,\
> Framed-MTU = 1500,\
> Framed-Compression = Van-Jacobson-TCP-IP,\
> Class = %{NAS-Port}
> </AuthBy>
>
> <AuthBy FILE>
> Identifier TimeZone
> Filename %D/adsl.users
> </AuthBy>
>
> <Handler Request-Type=Accounting-Request>
> AuthBy RADMINAUTH
> </Handler>
>
> <Handler Realm=test1>
> AuthBy TimeZone
> </Handler>
>
> <Handler Realm=test2>
> AuthBy WithOutIdleTimeout
> </Handler>
>
> <Handler>
> AuthBy WithIdleTimeout
> </Handler>
>
>
> # Handle User with NO Realm with RADMIN
> #<Realm>
> # AuthBy RADMINAUTH
> #</Realm>
>
> # Handle everyone with RADMIN
> #<Realm DEFAULT>
> # AuthBy RADMINAUTH
> #</Realm>
>
> <SessionDatabase SQL>
> # This database spec usually should be exactly the same
> # as in <AuthBy RADMIN> above
> DBSource dbi:ODBC:Radmin
> DBUsername xxxx
> DBAuth xxxx
> ClearNasQuery
> </SessionDatabase>
--
Radiator: the most portable, flexible and configurable RADIUS server
anywhere. Available on *NIX, *BSD, Windows 95/98/2000, NT, MacOS X.
-
Nets: internetwork inventory and management - graphical, extensible,
flexible with hardware, software, platform and database independence.
===
Archive at http://www.open.com.au/archives/radiator/
Announcements on radiator-announce at open.com.au
To unsubscribe, email 'majordomo at open.com.au' with
'unsubscribe radiator' in the body of the message.
More information about the radiator
mailing list